FDSP is the supplier for the Feed machinery, Biomass machinery, Fertilizer machinery and Steel Silo Get a Quote
    Home   |  
  1. News
  2.   |  
  3. Industry News

The correct installation and use of feed crusher

2021-05-18

The quality of finished feed products and the service life of feed machinery and equipment are closely related to your usual installation and use habits. Liangyou Stock (FDSP) lists the following points for attention, which can allow you to improve efficiency and stabilize production. If you have more questions, please feel free to contact us:

1. The crusher mixer must be fixedly installed, and the axis of the crusher pulley and the power machine pulley should be parallel, and the grooves of the two drive pulleys must be in the same straight line. Otherwise, it will not only accelerate the damage of the parts, but also easily drop the belt.

2. If the pulley needs to be modified, it must be calculated to meet the needs of the spindle speed of the crushing mixer. Do not increase the spindle speed at will. When it exceeds 15% of the rated speed, the machine will vibrate violently.

3. The raw materials should be carefully cleaned in advance, and sieved or selected if necessary to prevent iron and stones from entering the machine.

4. Before each use, open the cover of the crusher and check whether there is any damage to all parts of the machine, especially whether the split pin on the rotor is intact and whether the connection is loose. After confirming that it is intact, close the cover firmly and screw in the handwheel on the door. Drag the belt by hand to check whether the moving part is flexible, whether there are abnormal noises and jams.

5. After the crusher is started, it needs to run idling for 2-3 minutes, and then gradually add materials after it runs normally.

 

6. The operator should tighten the cuffs, wear a mask, and work with gloves is strictly prohibited; when feeding materials, stand on the side of the crusher to prevent rebound debris from hurting the face; when crushing long-stalk crops, do not pinch your hands to prevent The hand was pulled back by the crop and injured.

7. The feeding should follow the principle of "uniform feeding, small amount and quick feeding", that is, from less to more, until the load is normal, and maintain continuous and uniform to prevent "traffic jam".

8. If the material inlet is blocked, it is not allowed to poke with wooden or iron rods to prevent the sticks from being brought into the machine or ejected and hurting people. It is also not allowed to reach into the material inlet to shift the material. You can use a harder stem to The raw materials are pushed into the crushing chamber.

9. Pay close attention to the operation. If vibration, abnormal noise, blockage or spraying materials are found, stop the machine immediately for inspection and eliminate it. Bad machine.

10. It is strictly forbidden to open the door when the crusher is running; the belt drive should be equipped with protective devices; long-term overload operation is prohibited; various tools are not allowed to be placed on the crusher and materials at will, so as not to fall into the machine; smoking is prohibited in the workplace. Pay attention to waterproof and moisture-proof.

11. The self-made powder bag should be made of fabric with good air permeability, and the length should not be shorter than 1.5m. If the powder bag is not ventilated or too short, it may cause back spray at the inlet. 12. The feeding should be stopped before the machine is shut down, and the machine should be shut down after the materials in the standby are drained. After the operation, the dust and lubrication should be timely removed.

 

 

 

About Us

Jiangsu Liangyou Zhengda Co.,Ltd. (FDSP) was founded in the year of 2003, has a professional team of 150 people and a 35,000 square meter factory; we can design project plans according to the different needs of customers and provide 3D renderings; design solutions according to different customer requirements, different raw materials, and different sites; the company has a professional technical te...

Contact Us

E-mail: info@fdsp.com

Whatsapp: 8613961106628

No.558 Hongsheng Road, Liyang, Jiangsu, China

Copyright © Jiangsu Liangyou Zhengda Co., Ltd. (FDSP) All Rights Reserved. Propesyonal na Feed Machinery / Fertilizer Machinery / Biomass Machinery / Steel Silo Manufacturer Sitemap

Quote Whatsapp
Send Inquiry

Get a Quote

Get a quote, Learn more about products

We provide quotations, solutions and products based on the information you fill in, please fill in your needs and project description in detail
We'll get back to you in 1 business days. Whatsapp:8613961106628