FDSP is the supplier for the Feed machinery, Biomass machinery, Fertilizer machinery and Steel Silo Get a Quote
    Home   |  
  1. News
  2.   |  
  3. Industry News

Learn daily maintenance of grinder equipment

2021-05-18

Learn to maintain the shredder equipment daily

 

In order to better use the feed grinder and reduce the incidence of failures, Liangyou shares here briefly introduces the maintenance of the feed grinder, and reminds users to do daily maintenance, so that the mechanical equipment can better extend the life. Create benefits.
       1. Screen

The screen of the feed grinder is made of punching thin steel plate or iron sheet. When the screen is worn or punctured by foreign objects, it needs to be overhauled. If the damaged area is not large, it can be repaired by riveting or soldering. If the damaged area is large, a new screen should be replaced. When installing a new screen, pay attention to the fact that the rough side of the screen holes should face inward and the smooth side should face outwards. At the same time, the screen and the screen frame should be tightly fitted. When installing the ring screen, the stubble should follow the direction of rotation to prevent the material from jamming at the overlap.
       2. Bearing

After every 300 hours of operation of the feed grinder, the bearings should be washed once. If the bearing is lubricated by engine oil, it is advisable to fill the gap of the bearing seat by 1/3 when adding new engine oil, and not more than 1/2 at most. You only need to tighten the constant cover oil ring cap a little before operation. When the bearings of the feed grinder are severely worn or damaged, they should be replaced in time, and attention should be paid to strengthen the lubrication.
       Three, tooth claw

Among the components of the claw feed mill, the crushing claw is a vulnerable part, and it is also the main component that affects the quality and production efficiency of feed crushing. Therefore, the crushing claw should be replaced in time after it is worn out. When replacing the claws, pull out the disc first. Note that before pulling out the disc, you must first open the round nut lock plate on the back of the disc, use a hook wrench to unscrew the round reel, and then use the special puller to pull the disc out. In order to ensure the balanced operation of the rotor, pay attention to complete replacement when changing the claws. When assembling the claws, be sure to tighten the oyster mother and be careful not to miss the spring washer. In addition, qualified parts should be selected when changing the claws, and the weight difference of a single claw should not exceed 1 to 5 grams.
      Fourth, the hammer

Some of the hammer blades of the hammer type feed mill are symmetrical. When the sharp angle of the hammer blade is blunt, it can be used by adjusting the angle on the reverse side; if one end and two corners are worn, it should be turned around. When adjusting the angle or turning the head, all the hammers should be carried out at the same time; after the four corners of the hammers are worn, all should be replaced, and the weight difference of each group of hammers should not be more than 5 grams. In addition, the pin shaft of the fixed hammer and the round hole of the mounting pin shaft will be gradually ground due to wear, and the round hole will gradually become larger. When the pin shaft diameter is reduced by 1 mm from the original size, the diameter of the round hole shaft will be ground to the original size. When it is 1 mm larger, the main shaft, disc, positioning sleeve, claw (hammer) and pin shaft should be welded and repaired or replaced in time, and static balance test should be done to maintain the balance of the rotor, prevent the vibration of the unit, and cause crushing. The machine works stably.

Jiangsu Liangyou Chia Tai Co., Ltd. has specialized in the production of various types of shredders for many years, with a number of national patents, 24/7 technical consultation, after-sales service, rapid response, and always solving various practical production problems for customers.

 

 

 

About Us

Jiangsu Liangyou Zhengda Co.,Ltd. (FDSP) was founded in the year of 2003, has a professional team of 150 people and a 35,000 square meter factory; we can design project plans according to the different needs of customers and provide 3D renderings; design solutions according to different customer requirements, different raw materials, and different sites; the company has a professional technical te...

Contact Us

E-mail: info@fdsp.com

Whatsapp: 8613961106628

No.558 Hongsheng Road, Liyang, Jiangsu, China

Copyright © Jiangsu Liangyou Zhengda Co., Ltd. (FDSP) All Rights Reserved. Propesyonal na Feed Machinery / Fertilizer Machinery / Biomass Machinery / Steel Silo Manufacturer Sitemap

Quote Whatsapp
Send Inquiry

Get a Quote

Get a quote, Learn more about products

We provide quotations, solutions and products based on the information you fill in, please fill in your needs and project description in detail
We'll get back to you in 1 business days. Whatsapp:8613961106628